Trouble with MHET v2.0 board and v9 and v11 hyperserialesp32 - Running HyperHDR v21 stable #138

reedy-au · 2026-06-27T13:12:48Z

reedy-au
Jun 27, 2026

Hi All,

Hope you are well.

I've been running hyper hdr v18 and hyperserialesp32 v7 for a while now. I got a new TV and decided to upgrade hyper software.

I'm running libreelec 12.2.1 on intel nuc i511. I know there's an addon but I'd prefer just to use the linux tarball with static libs for testing purposes. I had no joy with the addon.

To get v21.0 hyperhdr stable working I had to copy some libraries from "elsewhere" (previous hyperhdr version) to ~/hyperhdr/share/hyperhdr/lib/

And it started up fine with no errors afterwards. Happy days.

I have a lot of mhet v1 and v2 boards from other things and these work fine as the LED controller when using v7 and v7 of hyperserialesp32.bin but when I flash(successfully) v9 or v11 there is no LED response.

The serial port is opened according to the logs in HyperHDR and the board and flashed version are detected OK:
22:41:07.935 LEDDEVICE0_ADALIGHT : Serial port auto-discovery. Found serial port device: USB Single Serial (/dev/ttyACM0 => ttyACM0)
22:41:07.935 LEDDEVICE0_ADALIGHT : Opening UART: ttyACM0
22:41:07.935 LEDDEVICE0_ADALIGHT : ProviderSerial.cpp:209:tryOpen() | _serialPort.open(QIODevice::ReadWrite): ttyACM0, Baud rate [2000000]bps
22:41:07.946 LEDDEVICE0_ADALIGHT : ProviderSerial.cpp:214:tryOpen() | portName: ttyACM0
22:41:07.946 LEDDEVICE0_ADALIGHT : ProviderSerial.cpp:215:tryOpen() | systemLocation: /dev/ttyACM0
22:41:07.946 LEDDEVICE0_ADALIGHT : ProviderSerial.cpp:216:tryOpen() | description: USB Single Serial
22:41:07.946 LEDDEVICE0_ADALIGHT : ProviderSerial.cpp:217:tryOpen() | manufacturer: 1a86
22:41:07.946 LEDDEVICE0_ADALIGHT : ProviderSerial.cpp:218:tryOpen() | productIdentifier: 0x55d4
22:41:07.946 LEDDEVICE0_ADALIGHT : ProviderSerial.cpp:219:tryOpen() | vendorIdentifier: 0x1a86
22:41:07.946 LEDDEVICE0_ADALIGHT : ProviderSerial.cpp:220:tryOpen() | serialNumber: 567E050638
22:41:08.250 LEDDEVICE0_ADALIGHT : ESP sent: ''
22:41:08.316 LEDDEVICE0_ADALIGHT : DETECTED DEVICE USING HyperSerialEsp8266/HyperSerialESP32/HyperSerialPico FIRMWARE (Welcome! Awa driver 9. NeoPixelBus SK6812 cold GRBW. RGBW => Gain: 255/255, red: 160, green: 160, blue: 160) at 66 msec

I am using the latest version (5.8) of esptool to flash the factory firmwares at offset 0x0
I've also tried to flash the factory.bin then the base binary afterwards to offset 0x10000

The only thing I've noticed is when I connect to the serial port to check for v7 & v8, I get the response:
python3 -m serial.tools.miniterm /dev/ttyACM0 2000000
--- Miniterm on /dev/ttyACM0 2000000,8,N,1 ---
--- Quit: Ctrl+] | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---

Welcome!
Awa driver 8.
NeoPixelBus SK6812 cold GRBW.

RGBW => Gain: 255/255, red: 160 , green: 160 , blue: 160
HyperHDR frames: 0 (FPS), receiv.: 0, good: 0, incompl.: 0, mem: 3568, heap: 365572
RGBW => Gain: 255/255, red: 160 , green: 160 , blue: 160
HyperHDR frames: 0 (FPS), receiv.: 0, good: 0, incompl.: 0, mem: 3536, heap: 365572
RGBW => Gain: 255/255, red: 160 , green: 160 , blue: 160

-----------------and it keeps going forever until handshake

HOWEVER, when I connect to the serial port for v9 and v11 it only displays an output ONCE:
root@opc01:/home/user/Downloads/HyperHDR/esptool/esptool-linux-amd64# python3 -m serial.tools.miniterm /dev/ttyACM0 2000000
--- Miniterm on /dev/ttyACM0 2000000,8,N,1 ---
--- Quit: Ctrl+] | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---
<␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀␀ crap omitted>
Welcome!
Awa driver 9.
NeoPixelBus SK6812 cold GRBW.
RGBW => Gain: 255/255, red: 160, green: 160, blue: 160

Then that's it.

I'm pretty stuck at this point . Should v9 & v11 hyperserialesp work with hyperHDR 21.0+ ?

I've also noted that once flashed with v9 and v11 they do not work hyperhdr18 but this part is documented, iirc to require v19.2beta at least.

At this point I have 2 working setups with hyperserialesp32 v8 and hyperhdr v21. It's working fine but latest software improvements and all that.

Please help before I go more crazy.

Thank you

awawa-dev · 2026-06-27T13:17:00Z

awawa-dev
Jun 27, 2026
Maintainer

Hi
You dont need serial port terminal to test LED output. It's in the HyperHDR logs when you stop the device. Follow this guide: https://www.hyperhdr.eu/2023/02/ultimate-guide-on-how-to-build-led.html#chapter9

0 replies

reedy-au · 2026-06-27T13:41:53Z

reedy-au
Jun 27, 2026
Author

Unfortunately after doing that the LED's are not turned on.

23:28:57.305 LEDDEVICE0_ADALIGHT 23:28:57.305 LEDDEVICE0_ADALIGHT 23:28:57.305 LEDDEVICE0_ADALIGHT 23:28:57.305 LEDDEVICE0_ADALIGHT 23:28:57.305 COMPONENTCTRL0 23:28:57.305 LEDDEVICE0_ADALIGHT 23:28:57.323 SMOOTHING0 23:28:57.324 EFFECTENGINE0 23:28:57.324 EFFECTENGINE0 23:28:57.324 MUXER0 23:28:57.324 HYPERHDR0 23:28:57.324 EFFECT0(Rainbo...) 23:28:57.324 MUXER0 23:28:57.324 MUXER0 23:28:57.324 SMOOTHING0 23:28:57.324 SMOOTHING0 23:28:57.324 LEDDEVICE0_ADALIGHT 23:28:57.324 SMOOTHING0 23:28:57.324 LEDDEVICE0_ADALIGHT 23:28:57.324 SMOOTHING0 23:28:57.324 LEDDEVICE0_ADALIGHT 23:28:57.324 HYPERHDR0 23:28:57.324 LEDDEVICE0_ADALIGHT 23:28:57.324 COLORSPACE_CALIBRATION : 23:28:57.324 LEDDEVICE0_ADALIGHT 23:28:57.324 LEDDEVICE0_ADALIGHT 23:28:57.324 IMAGETOLED_MNG0 23:28:57.404 SMOOTHING0 23:28:57.425 WEBSOCKET 23:28:57.437 WEBSOCKET 23:28:57.437 NET_DISCOVERY 23:28:58.406 SERVICE_mDNS 23:29:07.326 MUXER0 23:29:07.326 MUXER0 23:29:07.326 SMOOTHING0 23:29:07.326 SMOOTHING0 23:29:07.326 SMOOTHING0 23:29:07.326 LEDDEVICE0_ADALIGHT 23:29:07.327 SMOOTHING0 23:29:07.327 HYPERHDR0 23:29:07.327 LEDDEVICE0_ADALIGHT 23:29:07.327 COLORSPACE_CALIBRATION : 23:29:07.327 LEDDEVICE0_ADALIGHT 23:29:07.327 LEDDEVICE0_ADALIGHT 23:29:07.327 LEDDEVICE0_ADALIGHT 23:29:07.327 LEDDEVICE0_ADALIGHT 23:29:07.336 IMAGETOLED_MNG0 23:29:07.338 EFFECT0(Rainbo...) 23:29:07.338 EFFECTENGINE0 SmartPointer is removing: 23:29:07.338 EFFECT0(Rainbo...) 23:29:07.367 SMOOTHING0 23:29:22.539 MUXER0 23:29:22.539 MUXER0 23:29:22.539 MUXER0 23:29:22.539 HYPERHDR0 23:29:29.009 WEBSOCKET 23:29:29.091 WEBSOCKET 23:29:57.798 WEBSOCKET 23:29:57.809 WEBSOCKET 23:30:11.303 WEBSOCKET 23:30:16.668 SMOOTHING0 23:30:16.668 SMOOTHING0 23:30:16.668 SMOOTHING0 23:30:16.668 LEDDEVICE0_ADALIGHT 23:30:16.668 COMPONENTCTRL0 23:30:16.668 LEDDEVICE0_ADALIGHT 23:30:16.668 SMOOTHING0 23:30:16.668 LEDDEVICE0_ADALIGHT 23:30:16.668 SMOOTHING0 23:30:16.668 LEDDEVICE0_ADALIGHT 23:30:16.668 LEDDEVICE0_ADALIGHT 23:30:21.707 WEBSOCKET 23:30:21.719 WEBSOCKET SmartPointer is removing: LedDevice
23:30:28.384 LEDDEVICE0_ADALIGHT 23:30:28.384 LEDDEVICE0_ADALIGHT 23:30:28.385 LEDDEVICE0_ADALIGHT 23:30:28.385 LEDDEVICE0_ADALIGHT 23:30:28.385 LEDDEVICE0_ADALIGHT 23:30:28.394 LEDDEVICE0_ADALIGHT 23:30:28.435 LEDDEVICE0_ADALIGHT RGBW => Gain: 255/255, 23:30:28.438 LEDDEVICE0_ADALIGHT 23:30:28.438 LEDDEVICE0_ADALIGHT 23:30:28.438 LEDDEVICE0_ADALIGHT 23:30:28.438 LEDDEVICE0_ADALIGHT 23:30:28.438 LEDDEVICE0_ADALIGHT 23:30:28.439 LEDDEVICE0_ADALIGHT 23:30:28.439 LEDDEVICE0_ADALIGHT 23:30:28.439 LEDDEVICE0_ADALIGHT 23:30:28.439 LEDDEVICE0_ADALIGHT 23:30:28.439 LEDDEVICE0_ADALIGHT 23:30:28.439 LEDDEVICE0_ADALIGHT 23:30:28.439 LEDDEVICE0_ADALIGHT 23:30:28.439 LEDDEVICE0_ADALIGHT 23:30:28.439 LEDDEVICE0_ADALIGHT 23:30:28.439 LEDDEVICE0_ADALIGHT 23:30:28.439 LEDDEVICE0_ADALIGHT 23:30:28.439 LEDDEVICE0_ADALIGHT 23:30:28.439 LEDDEVICE0_ADALIGHT 23:30:28.439 LEDDEVICE0_ADALIGHT 23:30:28.439 LEDDEVICE0_ADALIGHT 23:30:28.439 LEDDEVICE0_ADALIGHT 23:30:28.440 COMPONENTCTRL0 23:30:28.450 LEDDEVICE0_ADALIGHT 23:30:28.450 LEDDEVICE0_ADALIGHT 23:30:28.450 LEDDEVICE0_ADALIGHT 23:30:28.450 LEDDEVICE0_ADALIGHT 23:30:28.450 LEDDEVICE0_ADALIGHT 23:30:28.461 LEDDEVICE0_ADALIGHT 23:30:28.461 LEDDEVICE0_ADALIGHT 23:30:28.461 LEDDEVICE0_ADALIGHT 23:30:28.471 LEDDEVICE0_ADALIGHT 23:30:28.471 LEDDEVICE0_ADALIGHT 23:30:28.471 LEDDEVICE0_ADALIGHT 23:30:28.471 LEDDEVICE0_ADALIGHT 23:30:28.471 LEDDEVICE0_ADALIGHT 23:30:28.471 LEDDEVICE0_ADALIGHT 23:30:28.471 LEDDEVICE0_ADALIGHT 23:30:28.775 LEDDEVICE0_ADALIGHT 23:30:28.841 LEDDEVICE0_ADALIGHT 23:30:28.841 LEDDEVICE0_ADALIGHT 23:30:28.841 LEDDEVICE0_ADALIGHT 23:30:28.841 COMPONENTCTRL0 23:30:53.036 WEBSOCKET 23:30:56.757 V4L2:AUTO 23:31:09.693 WEBSOCKET 23:31:19.098 WEBSOCKET 23:31:56.758 PERFORMANCE 23:32:56.757 PERFORMANCE 23:33:56.757 PERFORMANCE 23:34:29.847 SMOOTHING0 23:34:29.847 SMOOTHING0 23:34:29.848 LEDDEVICE0_ADALIGHT 23:34:29.848 LEDDEVICE0_ADALIGHT 23:34:29.848 LEDDEVICE0_ADALIGHT 23:34:29.857 LEDDEVICE0_ADALIGHT 23:34:30.285 LEDDEVICE0_ADALIGHT 23:34:30.286 COMPONENTCTRL0 23:34:30.286 PERFORMANCE 23:34:40.811 WEBSOCKET 23:34:56.757 PERFORMANCE 23:35:56.756 PERFORMANCE 23:36:56.756 PERFORMANCE 23:36:57.886 WEBSOCKET 23:36:59.236 SMOOTHING0 23:36:59.236 SMOOTHING0 23:36:59.237 LEDDEVICE0_ADALIGHT 23:36:59.248 LEDDEVICE0_ADALIGHT 23:36:59.248 LEDDEVICE0_ADALIGHT 23:36:59.248 LEDDEVICE0_ADALIGHT 23:36:59.248 LEDDEVICE0_ADALIGHT 23:36:59.248 LEDDEVICE0_ADALIGHT 23:36:59.258 LEDDEVICE0_ADALIGHT 23:36:59.258 LEDDEVICE0_ADALIGHT 23:36:59.258 LEDDEVICE0_ADALIGHT 23:36:59.269 LEDDEVICE0_ADALIGHT 23:36:59.269 LEDDEVICE0_ADALIGHT 23:36:59.269 LEDDEVICE0_ADALIGHT 23:36:59.269 LEDDEVICE0_ADALIGHT 23:36:59.269 LEDDEVICE0_ADALIGHT 23:36:59.269 LEDDEVICE0_ADALIGHT 23:36:59.269 LEDDEVICE0_ADALIGHT 23:36:59.573 LEDDEVICE0_ADALIGHT 23:36:59.639 LEDDEVICE0_ADALIGHT 23:36:59.639 LEDDEVICE0_ADALIGHT 23:36:59.639 LEDDEVICE0_ADALIGHT 23:36:59.639 COMPONENTCTRL0 23:37:52.741 WEBSOCKET 23:38:03.921 SMOOTHING0 23:38:03.921 SMOOTHING0 23:38:03.921 SMOOTHING0 23:38:03.921 LEDDEVICE0_ADALIGHT 23:38:03.921 COMPONENTCTRL0 23:38:03.921 LEDDEVICE0_ADALIGHT 23:38:03.921 SMOOTHING0 23:38:03.921 LEDDEVICE0_ADALIGHT 23:38:03.921 SMOOTHING0 23:38:03.921 LEDDEVICE0_ADALIGHT 23:38:03.921 SMOOTHING0 23:38:03.921 LEDDEVICE0_ADALIGHT 23:38:03.921 LEDDEVICE0_ADALIGHT 23:38:03.921 SMOOTHING0 23:38:03.921 LEDDEVICE0_ADALIGHT 23:38:03.921 LEDDEVICE0_ADALIGHT 23:38:03.921 LEDDEVICE0_ADALIGHT 23:38:03.922 SMOOTHING0 23:38:03.951 SMOOTHING0 23:38:48.539 SMOOTHING0 23:38:48.539 SMOOTHING0 23:38:48.539 SMOOTHING0 23:38:56.766 PERFORMANCE 23:39:00.587 SMOOTHING0 23:39:00.587 SMOOTHING0 23:39:00.587 SMOOTHING0 23:39:00.587 SMOOTHING0 23:39:00.587 SMOOTHING0 23:39:00.587 LEDDEVICE0_ADALIGHT 23:39:00.587 LEDDEVICE0_ADALIGHT 23:39:00.587 LEDDEVICE0_ADALIGHT 23:39:00.587 LEDDEVICE0_ADALIGHT 23:39:00.587 LEDDEVICE0_ADALIGHT 23:39:00.588 SMOOTHING0 23:39:00.628 SMOOTHING0 23:39:09.806 SMOOTHING0 23:39:09.806 SMOOTHING0 23:39:09.806 SMOOTHING0 23:39:56.768 PERFORMANCE : DETECTED DEVICE USING HyperSerialEsp8266/HyperSerialESP32/HyperSerialPico FIRMWARE (Welcome! Awa driver 9. NeoPixelBus SK6812 cold GRBW. RGBW => Gain: 255/255, red: 160, green: 160, blue: 160) at 66 msec
: LedDevice.cpp:63:switchOn() | Switch on
: LedDevice.cpp:139:powerOn() | Power On
: LedDevice.cpp:366:startRefreshTimer() | Starting timer with interval = 20ms
: LED device: enabled
: LedDevice.cpp:246:enable() | Enable the device
: Using alternative smoothing input (0)
: Run effect "Rainbow swirl fast" on channel 0
: EffectEngine.cpp:92:runEffectScript() | Start the effect: name [Rainbow swirl fast]
: Register new input 'System/EFFECT' with priority 0 as inactive
: Boot effect: animation set to 'Rainbow swirl fast' [started]
: Begin playing the effect with priority: 0
: Priority 0 is now active
: Set visible priority to 0
: Clearing queued colors before: enabling. Smoothing configuration changed: restarting timer.
: Smoothing queue is cleared
: LedDevice.cpp:380:stopRefreshTimer() | Stopping refresh timer
: Selecting config (1) => type: Linear, pause: false, settlingTime: 200ms, interval: 40ms (25Hz), antiFlickTres: 0, antiFlickStep: 0, antiFlickTime: 0
: Ignoring user LED refresh rate. Forcing smoothing refresh rate = 25.00 Hz
: Using linear smoothing input (1)
: LedDevice.cpp:422:setRefreshTime() | Refresh rate = 25.00 Hz
: New priority[0], previous [240]
: LedDevice.cpp:366:startRefreshTimer() | Starting timer with interval = 40ms
ColorSpaceCalibration.cpp:224:setBackLightEnabled() | setBackLightEnabled: 0
: LedDevice.cpp:432:setRefreshTime() | Refresh interval updated to 40ms
: LedDevice.cpp:447:smoothingRestarted() | LED refresh interval adjustment caused by smoothing configuration change to 40ms (proposed: 40ms)
: Total index number is: 1200 (memory: 1200). User sparse processing is: disabled, image size: 80 x 45, area number: 300
: Using linear smoothing procedure (1)
: HyperAPI.cpp:1097:handleLedDeviceCommand() | message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":392}]
: HyperAPI.cpp:1121:handleLedDeviceCommand() | response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"USB Single Serial (/dev/ttyACM0)","value":"ttyACM0"},{"name":" (/dev/ttyS0)","value":"ttyS0"},{"name":" (/dev/ttyS1)","value":"ttyS1"},{"name":" (/dev/ttyS2)","value":"ttyS2"},{"name":" (/dev/ttyS3)","value":"ttyS3"}],"ledDeviceType":"adalight"}]
: Found ESP board at ttyACM0:-1 (USB Single Serial)
: Starting the network discovery thread
: Timeout clear for priority 0
: Set visible priority to 240
: Clearing queued colors before: enabling. Smoothing configuration changed: restarting timer.
: Smoothing queue is cleared
: Selecting config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
: LedDevice.cpp:380:stopRefreshTimer() | Stopping refresh timer
: Using alternative smoothing input (0)
: New priority[240], previous [0]
: Ignoring user LED refresh rate. Forcing smoothing refresh rate = 50.00 Hz
ColorSpaceCalibration.cpp:224:setBackLightEnabled() | setBackLightEnabled: 1
: LedDevice.cpp:422:setRefreshTime() | Refresh rate = 50.00 Hz
: LedDevice.cpp:366:startRefreshTimer() | Starting timer with interval = 20ms
: LedDevice.cpp:432:setRefreshTime() | Refresh interval updated to 20ms
: LedDevice.cpp:447:smoothingRestarted() | LED refresh interval adjustment caused by smoothing configuration change to 20ms (proposed: 20ms)
: Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
: The effect quits with priority: 0
: Effect 'Rainbow swirl fast' has finished.
effect0/0 => "Rainbow swirl fast"
: Effect named: 'Rainbow swirl fast' is deleted
: Using alternative smoothing procedure (0)
: Removed source priority 254
: Register new input 'System/COLOR' with priority 254 as inactive
: Priority 254 is now active
: Background effect: color set to [255, 138, 0]
: WebSocketClient.cpp:189:sendClose() | send close: 1000
: WebSocketClient.cpp:40:WebSocketClient() | New connection from ::ffff:10.1.2.240
: HyperAPI.cpp:1097:handleLedDeviceCommand() | message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":773}]
: HyperAPI.cpp:1121:handleLedDeviceCommand() | response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"USB Single Serial (/dev/ttyACM0)","value":"ttyACM0"},{"name":" (/dev/ttyS0)","value":"ttyS0"},{"name":" (/dev/ttyS1)","value":"ttyS1"},{"name":" (/dev/ttyS2)","value":"ttyS2"},{"name":" (/dev/ttyS3)","value":"ttyS3"}],"ledDeviceType":"adalight"}]
: HyperAPI.cpp:1097:handleLedDeviceCommand() | message: [{"command":"leddevice","ledDeviceType":"","params":{},"subcommand":"hasLedClock","tan":1}]
: High resolution clock is NOT STEADY!
: Clearing queued colors before: disabling
: Smoothing queue is cleared
: LedDevice.cpp:380:stopRefreshTimer() | Stopping refresh timer
: Smoothing: disabled
: LedDevice.cpp:422:setRefreshTime() | Refresh rate = 50.00 Hz
: Creating config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
: LedDevice.cpp:366:startRefreshTimer() | Starting timer with interval = 20ms
: Selecting config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
: LedDevice.cpp:432:setRefreshTime() | Refresh interval updated to 20ms
: LedDevice.cpp:447:smoothingRestarted() | LED refresh interval adjustment caused by smoothing configuration change to 20ms (proposed: 0ms)
: HyperAPI.cpp:1097:handleLedDeviceCommand() | message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":415}]
: HyperAPI.cpp:1121:handleLedDeviceCommand() | response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"USB Single Serial (/dev/ttyACM0)","value":"ttyACM0"},{"name":" (/dev/ttyS0)","value":"ttyS0"},{"name":" (/dev/ttyS1)","value":"ttyS1"},{"name":" (/dev/ttyS2)","value":"ttyS2"},{"name":" (/dev/ttyS3)","value":"ttyS3"}],"ledDeviceType":"adalight"}]
: LedDevice.cpp:285:stop() | Stop device
: LedDevice.cpp:380:stopRefreshTimer() | Stopping refresh timer
: LedDevice.cpp:296:disable() | Disable the device
: LedDevice.cpp:89:switchOff() | Switch off
: LedDevice.cpp:543:writeBlack() | Set LED strip to black/power off
: ProviderSerial.cpp:146:close() | Flush was successful
: Received goodbye: 'HyperHDR frames: 83 (FPS), receiv.: 83, good: 83, incompl.: 0, mem1: 4212, mem2: 3232, heap: 301968
red:' (128)
: ProviderSerial.cpp:164:close() | Serial port is closed: ttyACM0
: Stopped LedDevice 'adalight'
: LedDevice.cpp:285:stop() | Stop device
: LedDevice.cpp:296:disable() | Disable the device
: Stopped LedDevice 'adalight'
: Start LedDevice 'adalight'.
: LedDevice.cpp:336:init() | deviceConfig: [{"awa_mode":true,"colorOrder":"rgb","currentLedCount":300,"espHandshake":true,"forceSerialDetection":false,"hardwareLedCount":null,"maxRetry":0,"output":"auto","rate":2000000,"refreshTime":0,"smoothingRefreshTime":0,"type":"adalight","white_channel_calibration":false}]
: LedDevice.cpp:432:setRefreshTime() | Refresh interval updated to 0ms
: ProviderSerial.cpp:50:init() | DeviceType : adalight
: ProviderSerial.cpp:51:init() | LedCount : 300
: ProviderSerial.cpp:52:init() | RefreshTime : 0
: ProviderSerial.cpp:67:init() | Device name : auto
: ProviderSerial.cpp:68:init() | Auto selection: 1
: ProviderSerial.cpp:69:init() | Baud rate : 2000000
: ProviderSerial.cpp:70:init() | ESP handshake : ON
: ProviderSerial.cpp:71:init() | Force ESP/Pico Detection : OFF
: ProviderSerial.cpp:72:init() | Delayed open : 0
: ProviderSerial.cpp:73:init() | Retry limit : 0
: DriverSerialAdalight.cpp:78:CreateHeader() | Adalight driver with activated high speeed & data integration check AWA protocol
: DriverSerialAdalight.cpp:87:CreateHeader() | Adalight header for 300 leds: Awa 0x01 0x2b 0x7f
: LedDevice.cpp:246:enable() | Enable the device
: LED device: disabled
: Serial port auto-discovery. Skipping this device for now: USB Single Serial (/dev/ttyACM0 => ttyACM0), VID: 0x1a86, PID: 0x55d4
: Serial port auto-discovery. Skipping this device for now: (/dev/ttyS0 => ttyS0), VID: 0x0, PID: 0x0
: Serial port auto-discovery. Skipping this device for now: (/dev/ttyS1 => ttyS1), VID: 0x0, PID: 0x0
: Serial port auto-discovery. Skipping this device for now: (/dev/ttyS2 => ttyS2), VID: 0x0, PID: 0x0
: Serial port auto-discovery. Skipping this device for now: (/dev/ttyS3 => ttyS3), VID: 0x0, PID: 0x0
: Serial port auto-discovery. Found serial port device: USB Single Serial (/dev/ttyACM0 => ttyACM0)
: Opening UART: ttyACM0
: ProviderSerial.cpp:209:tryOpen() | _serialPort.open(QIODevice::ReadWrite): ttyACM0, Baud rate [2000000]bps
: ProviderSerial.cpp:214:tryOpen() | portName: ttyACM0
: ProviderSerial.cpp:215:tryOpen() | systemLocation: /dev/ttyACM0
: ProviderSerial.cpp:216:tryOpen() | description: USB Single Serial
: ProviderSerial.cpp:217:tryOpen() | manufacturer: 1a86
: ProviderSerial.cpp:218:tryOpen() | productIdentifier: 0x55d4
: ProviderSerial.cpp:219:tryOpen() | vendorIdentifier: 0x1a86
: ProviderSerial.cpp:220:tryOpen() | serialNumber: 567E050638
: ESP sent: ''
: DETECTED DEVICE USING HyperSerialEsp8266/HyperSerialESP32/HyperSerialPico FIRMWARE (Welcome! Awa driver 9. NeoPixelBus SK6812 cold GRBW. RGBW => Gain: 255/255, red: 160, green: 160, blue: 160) at 66 msec
: LedDevice.cpp:63:switchOn() | Switch on
: LedDevice.cpp:139:powerOn() | Power On
: LED device: enabled
: HyperAPI.cpp:1097:handleLedDeviceCommand() | message: [{"command":"leddevice","ledDeviceType":"","params":{},"subcommand":"hasLedClock","tan":1}]
: Video cache: size: 2, hits: 7185, needed: 1, cleanup: 0, limit: 8
: WebSocketClient.cpp:40:WebSocketClient() | New connection from ::ffff:10.1.2.240
: HyperAPI.cpp:1097:handleLedDeviceCommand() | message: [{"command":"leddevice","ledDeviceType":"","params":{},"subcommand":"hasLedClock","tan":1}]
: [USB: FPS = 60.03, decoding = 0ms, frames = 3602, invalid = 0, mode = direct], [INSTANCE0: FPS = 60.03, processed = 3602], [LED0: FPS = 60.03, send = 3602, processed = 3602, dropped = 0]
: [USB: FPS = 60.03, decoding = 0ms, frames = 3602, invalid = 0, mode = direct], [INSTANCE0: FPS = 60.03, processed = 3602], [LED0: FPS = 60.03, send = 3602, processed = 3602, dropped = 0]
: [USB: FPS = 60.03, decoding = 0ms, frames = 3602, invalid = 0, mode = direct], [INSTANCE0: FPS = 60.03, processed = 3602], [LED0: FPS = 60.03, send = 3602, processed = 3602, dropped = 0]
: Clearing queued colors before: disabling
: Smoothing queue is cleared
: LedDevice.cpp:296:disable() | Disable the device
: LedDevice.cpp:89:switchOff() | Switch off
: LedDevice.cpp:543:writeBlack() | Set LED strip to black/power off
: ProviderSerial.cpp:146:close() | Flush was successful
: ProviderSerial.cpp:164:close() | Serial port is closed: ttyACM0
: LED device: disabled
: [USB: FPS = 60.03, decoding = 0ms, frames = 3602, invalid = 0, mode = direct], [INSTANCE0: FPS = 60.03, processed = 3602]
: HyperAPI.cpp:946:handleLoggingCommand() | log streaming activated for client ::ffff:10.1.2.240
: [USB: FPS = 60.03, decoding = 0ms, frames = 3602, invalid = 0, mode = direct], [INSTANCE0: FPS = 60.03, processed = 3602]
: [USB: FPS = 60.03, decoding = 0ms, frames = 3602, invalid = 0, mode = direct], [INSTANCE0: FPS = 60.03, processed = 3602]
: [USB: FPS = 60.03, decoding = 0ms, frames = 3602, invalid = 0, mode = direct], [INSTANCE0: FPS = 60.03, processed = 3602]
: HyperAPI.cpp:955:handleLoggingCommand() | log streaming deactivated for client ::ffff:10.1.2.240
: Clearing queued colors before: enabling
: Smoothing queue is cleared
: LedDevice.cpp:246:enable() | Enable the device
: Serial port auto-discovery. Skipping this device for now: USB Single Serial (/dev/ttyACM0 => ttyACM0), VID: 0x1a86, PID: 0x55d4
: Serial port auto-discovery. Skipping this device for now: (/dev/ttyS0 => ttyS0), VID: 0x0, PID: 0x0
: Serial port auto-discovery. Skipping this device for now: (/dev/ttyS1 => ttyS1), VID: 0x0, PID: 0x0
: Serial port auto-discovery. Skipping this device for now: (/dev/ttyS2 => ttyS2), VID: 0x0, PID: 0x0
: Serial port auto-discovery. Skipping this device for now: (/dev/ttyS3 => ttyS3), VID: 0x0, PID: 0x0
: Serial port auto-discovery. Found serial port device: USB Single Serial (/dev/ttyACM0 => ttyACM0)
: Opening UART: ttyACM0
: ProviderSerial.cpp:209:tryOpen() | _serialPort.open(QIODevice::ReadWrite): ttyACM0, Baud rate [2000000]bps
: ProviderSerial.cpp:214:tryOpen() | portName: ttyACM0
: ProviderSerial.cpp:215:tryOpen() | systemLocation: /dev/ttyACM0
: ProviderSerial.cpp:216:tryOpen() | description: USB Single Serial
: ProviderSerial.cpp:217:tryOpen() | manufacturer: 1a86
: ProviderSerial.cpp:218:tryOpen() | productIdentifier: 0x55d4
: ProviderSerial.cpp:219:tryOpen() | vendorIdentifier: 0x1a86
: ProviderSerial.cpp:220:tryOpen() | serialNumber: 567E050638
: ESP sent: ''
: DETECTED DEVICE USING HyperSerialEsp8266/HyperSerialESP32/HyperSerialPico FIRMWARE (Welcome! Awa driver 9. NeoPixelBus SK6812 cold GRBW. RGBW => Gain: 255/255, red: 160, green: 160, blue: 160) at 66 msec
: LedDevice.cpp:63:switchOn() | Switch on
: LedDevice.cpp:139:powerOn() | Power On
: LED device: enabled
: HyperAPI.cpp:1097:handleLedDeviceCommand() | message: [{"command":"leddevice","ledDeviceType":"","params":{},"subcommand":"hasLedClock","tan":1}]
: High resolution clock is NOT STEADY!
: Clearing queued colors before: enabling
: Smoothing queue is cleared
: LedDevice.cpp:422:setRefreshTime() | Refresh rate = 50.00 Hz
: Smoothing: enabled
: LedDevice.cpp:366:startRefreshTimer() | Starting timer with interval = 20ms
: Creating config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 15ms (66Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
: LedDevice.cpp:432:setRefreshTime() | Refresh interval updated to 20ms
: Clearing queued colors before: enabling. Smoothing configuration changed: restarting timer.
: LedDevice.cpp:447:smoothingRestarted() | LED refresh interval adjustment caused by smoothing configuration change to 20ms (proposed: 20ms)
: Smoothing queue is cleared
: LedDevice.cpp:380:stopRefreshTimer() | Stopping refresh timer
: LedDevice.cpp:422:setRefreshTime() | Refresh rate = 66.67 Hz
: Selecting config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 15ms (66Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
: LedDevice.cpp:366:startRefreshTimer() | Starting timer with interval = 15ms
: LedDevice.cpp:432:setRefreshTime() | Refresh interval updated to 15ms
: LedDevice.cpp:447:smoothingRestarted() | LED refresh interval adjustment caused by smoothing configuration change to 15ms (proposed: 15ms)
: Using alternative smoothing input (0)
: Using alternative smoothing procedure (0)
: High resolution clock is NOT STEADY!
: Creating config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 15ms (66Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
: Selecting config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 15ms (66Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
: [USB: FPS = 60.03, decoding = 0ms, frames = 3602, invalid = 0, mode = direct], [INSTANCE0: FPS = 59.53, processed = 3572], [LED0: FPS = 65.32, send = 3920, processed = 3920, dropped = 79]
: High resolution clock is NOT STEADY!
: Creating config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
: Clearing queued colors before: enabling. Smoothing configuration changed: restarting timer.
: Smoothing queue is cleared
: Selecting config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
: LedDevice.cpp:380:stopRefreshTimer() | Stopping refresh timer
: LedDevice.cpp:422:setRefreshTime() | Refresh rate = 50.00 Hz
: LedDevice.cpp:366:startRefreshTimer() | Starting timer with interval = 20ms
: LedDevice.cpp:432:setRefreshTime() | Refresh interval updated to 20ms
: LedDevice.cpp:447:smoothingRestarted() | LED refresh interval adjustment caused by smoothing configuration change to 20ms (proposed: 20ms)
: Using alternative smoothing input (0)
: Using alternative smoothing procedure (0)
: High resolution clock is NOT STEADY!
: Creating config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
: Selecting config (0) => type: Alternative, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
: [USB: FPS = 60.03, decoding = 0ms, frames = 3602, invalid = 0, mode = direct], [INSTANCE0: FPS = 60.05, processed = 3603], [LED0: FPS = 51.03, send = 3062, processed = 3062, dropped = 0]

0 replies

awawa-dev · 2026-06-27T14:04:59Z

awawa-dev
Jun 27, 2026
Maintainer

It's about logs not LED rendering at this point. Are you sure you followed the guide exactly as described?

0 replies

reedy-au · 2026-06-27T14:09:34Z

reedy-au
Jun 27, 2026
Author

Pretty sure...

I flash hyperserialesp32.bin version 7 to MHET board and it works fine.

I flash hyperserialesp32.bin version 9 or version 11 to MHET board and it does not work. No LED control even though hyperhdr says it's detected in the logs...

0 replies

awawa-dev · 2026-06-27T14:17:43Z

awawa-dev
Jun 27, 2026
Maintainer

Im not talking about that part right now. You need to proceed with the test procedure described in the link I gave you earlier.

0 replies

reedy-au · 2026-06-27T14:22:03Z

reedy-au
Jun 27, 2026
Author

I went through the testing procedure from the link you provided above and pasted the logs whilst doing so.

But why go through the test procedure with the MHET board does not control the LED strip?

What am I missing?

Thanks

0 replies

awawa-dev · 2026-06-27T14:25:14Z

awawa-dev
Jun 27, 2026
Maintainer

You need to read statistics described in the test procedure to make sure the board is receiving colors from HyperHDR. If it's receiving them, it's most likely an electrical/connection issue.

0 replies

reedy-au · 2026-06-27T17:29:46Z

reedy-au
Jun 27, 2026
Author

Guaranteed it's not a electrical issue. I have multiple mhet live boards that have different hyperserialesp32 versions on and I just rip them off the headers that are soldered on the pcb.

All versions above 7 do not work.

I plonk a v7 board in whilst it's all powered on and the leds start doing there thing...

Dunno.

Here's logs of me doing that. Maybe I've missed somthing.

I recompiled one of the v11 SK6812 firmwares with the actual board name itself and serial baud of 4000000 but no joy.

2026-06-28T03:17:09.168Z [CORE] TTY is not attached to the log output
2026-06-28T03:17:09.173Z [MAIN] Database path: '/storage/hyperhdr21/.hyperhdr/db/hyperhdr.db', readonlyMode = disabled
2026-06-28T03:17:09.173Z [MAIN] Starting HyperHdr - 21.0.0.0, (HEAD detached at v21.0.0.0) (Awawa-24e1675/803162c-1741515688), built: Mar 9 2025:10:34:31
2026-06-28T03:17:09.173Z [MAIN] Set user data path to '/storage/hyperhdr21/.hyperhdr'
2026-06-28T03:17:09.173Z [INSTANCE_CFG] Loading instance configuration
2026-06-28T03:17:09.173Z [DB] Database opened: /storage/hyperhdr21/.hyperhdr/db/hyperhdr.db
2026-06-28T03:17:09.179Z [INSTANCE_CFG] Settings database initialized
2026-06-28T03:17:09.194Z [SOUND_GRABBER] Sound device is disabled
2026-06-28T03:17:09.212Z [JSONSERVER] (JsonServer.cpp:26) Created new instance
2026-06-28T03:17:09.212Z [JSONSERVER] Started on port 19444
2026-06-28T03:17:09.212Z [SSDP] (SSDPHandler.cpp:31) SSDPHandler is initialized
2026-06-28T03:17:09.198Z [V4L2:USB3 Video: US] (GrabberWrapper.cpp:53) Starting the grabber wrapper
2026-06-28T03:17:09.198Z [V4L2:USB3 VIDEO: US] Found capture device: /dev/video0
2026-06-28T03:17:09.198Z [V4L2:USB3 VIDEO: US] (V4L2Grabber.cpp:425) Device has 'brightness' control => min: 0, max: 100, default: 50
2026-06-28T03:17:09.198Z [V4L2:USB3 VIDEO: US] (V4L2Grabber.cpp:431) Device has 'contrast' control => min: 0, max: 100, default: 50
2026-06-28T03:17:09.198Z [V4L2:USB3 VIDEO: US] (V4L2Grabber.cpp:437) Device has 'saturation' control => min: 0, max: 100, default: 50
2026-06-28T03:17:09.198Z [V4L2:USB3 VIDEO: US] (V4L2Grabber.cpp:443) Device has 'hue' control => min: 0, max: 100, default: 50
2026-06-28T03:17:09.198Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1920 x 1080 @ 60 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1920 x 1080 @ 50 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1920 x 1080 @ 30 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1920 x 1080 @ 20 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1920 x 1080 @ 10 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1600 x 1200 @ 60 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1600 x 1200 @ 50 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1600 x 1200 @ 30 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1600 x 1200 @ 20 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1600 x 1200 @ 10 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1360 x 768 @ 60 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1360 x 768 @ 50 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1360 x 768 @ 30 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1360 x 768 @ 20 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1360 x 768 @ 10 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 1024 @ 60 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 1024 @ 50 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 1024 @ 30 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 1024 @ 20 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 1024 @ 10 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 960 @ 60 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 960 @ 50 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 960 @ 30 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 960 @ 20 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 960 @ 10 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 720 @ 60 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 720 @ 50 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 720 @ 30 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 720 @ 20 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 720 @ 10 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1024 x 768 @ 60 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1024 x 768 @ 50 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1024 x 768 @ 30 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1024 x 768 @ 20 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1024 x 768 @ 10 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 800 x 600 @ 60 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 800 x 600 @ 50 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 800 x 600 @ 30 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 800 x 600 @ 20 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 800 x 600 @ 10 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 576 @ 60 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 576 @ 50 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 576 @ 30 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 576 @ 20 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 576 @ 10 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 480 @ 60 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 480 @ 50 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 480 @ 30 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 480 @ 20 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 480 @ 10 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 640 x 480 @ 60 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 640 x 480 @ 50 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 640 x 480 @ 30 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 640 x 480 @ 20 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 640 x 480 @ 10 fps yuyv input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1920 x 1080 @ 60 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1920 x 1080 @ 50 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1920 x 1080 @ 30 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1920 x 1080 @ 20 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1920 x 1080 @ 10 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1600 x 1200 @ 60 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1600 x 1200 @ 50 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1600 x 1200 @ 30 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1600 x 1200 @ 20 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1600 x 1200 @ 10 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1360 x 768 @ 60 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1360 x 768 @ 50 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1360 x 768 @ 30 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1360 x 768 @ 20 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1360 x 768 @ 10 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 1024 @ 60 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 1024 @ 50 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 1024 @ 30 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 1024 @ 20 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 1024 @ 10 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 960 @ 60 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 960 @ 50 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 960 @ 30 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 960 @ 20 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 960 @ 10 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 720 @ 60 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 720 @ 50 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 720 @ 30 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 720 @ 20 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1280 x 720 @ 10 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1024 x 768 @ 60 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1024 x 768 @ 50 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1024 x 768 @ 30 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1024 x 768 @ 20 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 1024 x 768 @ 10 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 800 x 600 @ 60 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 800 x 600 @ 50 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 800 x 600 @ 30 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 800 x 600 @ 20 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 800 x 600 @ 10 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 576 @ 60 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 576 @ 50 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 576 @ 30 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 576 @ 20 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 576 @ 10 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 480 @ 60 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 480 @ 50 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 480 @ 30 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 480 @ 20 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 720 x 480 @ 10 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 640 x 480 @ 60 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 640 x 480 @ 50 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 640 x 480 @ 30 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 640 x 480 @ 20 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] USB3 Video: USB3 Video (video0) [/dev/video0] 640 x 480 @ 10 fps mjpeg input 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] (V4L2Grabber.cpp:102) P010 was unsupported on the build machine
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] Restarting video grabber is now blocked due to reloading of the configuration
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] Cropping image: width=0 height=0; crop: left=0 right=0 top=0 bottom=0
2026-06-28T03:17:09.199Z [V4L2:USB3 Video: US] (GrabberWrapper.cpp:180) CEC keycode. Start: 0, stop: 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] (Grabber.cpp:390) setBrightnessContrastSaturationHue nothing changed
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] (V4L2Grabber.cpp:143) setHdrToneMappingMode to: Disabled
2026-06-28T03:17:09.199Z [AUTOTONEMAPPING] Tone mapping is currently: disabled
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] (Grabber.cpp:299) setFpsSoftwareDecimation to: 1
2026-06-28T03:17:09.199Z [SIGNAL_OLD] (DetectionManual.cpp:84) Signal detection area set to: 0.250000,0.250000 x 0.750000,0.750000
2026-06-28T03:17:09.199Z [SIGNAL_OLD] (DetectionManual.cpp:74) Signal threshold set to: {0, 0, 0} and frames: 50
2026-06-28T03:17:09.199Z [SIGNAL_AUTO] (DetectionAutomatic.cpp:375) Automatic signal detection -> errorTolerance: 9, modelTolerance: 90, sleepTime: 1000, wakeTime: 0
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] (Grabber.cpp:497) setDeviceVideoStandard preparing to restart video grabber. Old: '' new: 'USB3 Video: USB3 Video (video0)'
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] Delayed restart of the grabber due to change of selected device
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] (Grabber.cpp:317) Force encoding to: NO_CHANGE (old: NO_CHANGE)
2026-06-28T03:17:09.199Z [V4L2:USB3 VIDEO: US] setQFrameDecimation is now: disabled
2026-06-28T03:17:09.199Z [AUTOTONEMAPPING] Enabled: no, time to enable: 30s, time to disable: 500ms, thresholds: { 180, 175, 160}
2026-06-28T03:17:09.199Z [X11_SYSTEM:AUTO] Loaded X11 proxy library for screen capturing
2026-06-28T03:17:09.199Z [DAEMON] The system doesn't support the X11 system grabber
2026-06-28T03:17:09.199Z [HYPERHDR0] Starting the instance
2026-06-28T03:17:09.199Z [INSTANCE_CFG0] Loading instance configuration
2026-06-28T03:17:09.199Z [FRAMEBUFFER_SYSTEM:AUTO] Found FrameBuffer device: /dev/fb0
2026-06-28T03:17:09.199Z [FRAMEBUFFER_SYSTEM:AUTO] Restarting video grabber is now blocked due to reloading of the configuration
2026-06-28T03:17:09.199Z [FRAMEBUFFER_SYSTEM:AUTO] (Grabber.cpp:276) Set new width: 512, height: 512 for capture
2026-06-28T03:17:09.199Z [DB] Database opened: /storage/hyperhdr21/.hyperhdr/db/hyperhdr.db
2026-06-28T03:17:09.199Z [FRAMEBUFFER_SYSTEM:AUTO] (Grabber.cpp:452) setWidthHeight preparing to restarting video grabber 0
2026-06-28T03:17:09.199Z [FRAMEBUFFER_SYSTEM:AUTO] Delayed restart of the grabber due to change of the capturing resolution
2026-06-28T03:17:09.199Z [FRAMEBUFFER_SYSTEM:AUTO] Delayed restart of the grabber due to change of the framerate
2026-06-28T03:17:09.199Z [FRAMEBUFFER_SYSTEM:AUTO] (Grabber.cpp:238) Set hardware acceleration to enabled
2026-06-28T03:17:09.199Z [FRAMEBUFFER_SYSTEM:AUTO] Delayed restart of the grabber due to change of the hardware acceleration
2026-06-28T03:17:09.199Z [SIGNAL_OLD] (DetectionManual.cpp:84) Signal detection area set to: 0.250000,0.250000 x 0.750000,0.750000
2026-06-28T03:17:09.199Z [SIGNAL_OLD] (DetectionManual.cpp:74) Signal threshold set to: {12, 12, 12} and frames: 200
2026-06-28T03:17:09.199Z [FRAMEBUFFER_SYSTEM:AUTO] (Grabber.cpp:497) setDeviceVideoStandard preparing to restart video grabber. Old: '' new: 'auto'
2026-06-28T03:17:09.199Z [FRAMEBUFFER_SYSTEM:AUTO] Delayed restart of the grabber due to change of selected device
2026-06-28T03:17:09.199Z [X11_SYSTEM:auto] (SystemWrapper.cpp:70) Closing grabber: X11_SYSTEM:auto
2026-06-28T03:17:09.223Z [INSTANCE_CFG0] Settings database initialized
2026-06-28T03:17:09.223Z [COMPONENTCTRL0] (ComponentController.cpp:27) ComponentController is initialized. Components are ENABLED
2026-06-28T03:17:09.223Z [MUXER0] (Muxer.cpp:54) Muxer initialized
2026-06-28T03:17:09.224Z [BLACKBORDER] Set mode to: default
2026-06-28T03:17:09.224Z [COMPONENTCTRL0] Blackborder detector: enabled
2026-06-28T03:17:09.224Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:192) Set LED mapping type to advanced
2026-06-28T03:17:09.224Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:176) setSparseProcessing to 0
2026-06-28T03:17:09.224Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:103) ImageToLedManager initialized
2026-06-28T03:17:09.224Z [COLORSPACE_CALIBRATION0] classicMode: no, gammas:[1.50, 1.50, 1.50], saturation: 1.00, luminance: 1.00, backLight: [enabled, threshold: 1, colored: yes]
2026-06-28T03:17:09.224Z [LED_CALIBRATION0] (LedCalibration.cpp:101) Calibration config '0' for LED segment: [0, 299]
2026-06-28T03:17:09.224Z [HYPERHDR0] Led strip RGB order is: rgb
2026-06-28T03:17:09.224Z [SMOOTHING0] High resolution clock is NOT STEADY!
2026-06-28T03:17:09.224Z [SMOOTHING0] Creating config (0) => type: Linear, pause: false, settlingTime: 65ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
2026-06-28T03:17:09.224Z [SMOOTHING0] Clearing queued colors before: disabling. Smoothing configuration changed: restarting timer.
2026-06-28T03:17:09.224Z [SMOOTHING0] Smoothing queue is cleared
2026-06-28T03:17:09.224Z [SMOOTHING0] Selecting config (0) => type: Linear, pause: false, settlingTime: 65ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
2026-06-28T03:17:09.224Z [SMOOTHING0] Selecting config (0) => type: Linear, pause: false, settlingTime: 65ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
2026-06-28T03:17:09.224Z [LEDDEVICE0_ADALIGHT] Start LedDevice 'adalight'.
2026-06-28T03:17:09.224Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:336) deviceConfig: [{"awa_mode":true,"colorOrder":"rgb","currentLedCount":300,"espHandshake":true,"forceSerialDetection":false,"maxRetry":5,"output":"ttyACM0","rate":4000000,"refreshTime":0,"smoothingRefreshTime":0,"type":"adalight","white_channel_calibration":false}]
2026-06-28T03:17:09.224Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:432) Refresh interval updated to 0ms
2026-06-28T03:17:09.224Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:50) DeviceType : adalight
2026-06-28T03:17:09.224Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:51) LedCount : 300
2026-06-28T03:17:09.224Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:52) RefreshTime : 0
2026-06-28T03:17:09.224Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:67) Device name : ttyACM0
2026-06-28T03:17:09.224Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:68) Auto selection: 0
2026-06-28T03:17:09.224Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:69) Baud rate : 4000000
2026-06-28T03:17:09.224Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:70) ESP handshake : ON
2026-06-28T03:17:09.224Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:71) Force ESP/Pico Detection : OFF
2026-06-28T03:17:09.224Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:72) Delayed open : 0
2026-06-28T03:17:09.224Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:73) Retry limit : 5
2026-06-28T03:17:09.224Z [LEDDEVICE0_ADALIGHT] (DriverSerialAdalight.cpp:78) Adalight driver with activated high speeed & data integration check AWA protocol
2026-06-28T03:17:09.224Z [LEDDEVICE0_ADALIGHT] (DriverSerialAdalight.cpp:87) Adalight header for 300 leds: Awa 0x01 0x2b 0x7f
2026-06-28T03:17:09.224Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:246) Enable the device
2026-06-28T03:17:09.224Z [HYPER_MANAGER] HyperHDR instance 'First LED instance' has been started
2026-06-28T03:17:09.224Z [HYPERHDR0] The instance is running
2026-06-28T03:17:09.224Z [LEDDEVICE0_ADALIGHT] Opening UART: ttyACM0
2026-06-28T03:17:09.224Z [MUXER0] Register new input 'System/VIDEOGRABBER' with priority 240 as inactive
2026-06-28T03:17:09.224Z [COMPONENTCTRL0] Video capture device: enabled
2026-06-28T03:17:09.224Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): ttyACM0, Baud rate [4000000]bps
2026-06-28T03:17:09.224Z [V4L2:USB3 VIDEO: US] Multithreading for V4L2 is enabled. Available thread's count 4
2026-06-28T03:17:09.224Z [V4L2:USB3 VIDEO: US] Found capture device: /dev/video0
2026-06-28T03:17:09.224Z [V4L2:USB3 VIDEO: US] (V4L2Grabber.cpp:425) Device has 'brightness' control => min: 0, max: 100, default: 50
2026-06-28T03:17:09.224Z [V4L2:USB3 VIDEO: US] (V4L2Grabber.cpp:431) Device has 'contrast' control => min: 0, max: 100, default: 50
2026-06-28T03:17:09.224Z [V4L2:USB3 VIDEO: US] (V4L2Grabber.cpp:437) Device has 'saturation' control => min: 0, max: 100, default: 50
2026-06-28T03:17:09.224Z [V4L2:USB3 VIDEO: US] (V4L2Grabber.cpp:443) Device has 'hue' control => min: 0, max: 100, default: 50
2026-06-28T03:17:09.225Z [V4L2:USB3 VIDEO: US] (V4L2Grabber.cpp:232) Searching for USB3 Video: USB3 Video (video0) 0 x 0 @ 0 fps, input: -1 (NO_CHANGE)
2026-06-28T03:17:09.225Z [V4L2:USB3 VIDEO: US] Selected resolution not found in supported modes. Forcing best guess
2026-06-28T03:17:09.225Z [V4L2:USB3 VIDEO: US] *************************************************************************************************
2026-06-28T03:17:09.225Z [V4L2:USB3 VIDEO: US] Starting V4L2 grabber. Selected: USB3 Video: USB3 Video (video0) [/dev/video0] 800 x 600 @ 60 fps yuyv input -1
2026-06-28T03:17:09.225Z [V4L2:USB3 VIDEO: US] *************************************************************************************************
2026-06-28T03:17:09.225Z [V4L2:USB3 VIDEO: US] (V4L2Grabber.cpp:867) Hardware cropping is not supported: ignoring
2026-06-28T03:17:09.225Z [V4L2:USB3 VIDEO: US] Set device input to: Camera 1
2026-06-28T03:17:09.225Z [FLATBUFSERVER] Tone mapping: 0
2026-06-28T03:17:09.225Z [FLATBUFSERVER] Started on port 19400
2026-06-28T03:17:09.225Z [WEBSERVER] Initialize Webserver
2026-06-28T03:17:09.225Z [FLATBUFSERVER] Started local domain socket server: 'hyperhdr-domain'
2026-06-28T03:17:09.225Z [FLATBUFSERVER] Tone mapping: 0
2026-06-28T03:17:09.225Z [FLATBUFSERVER] NV12 quarter of frame mode: 0
2026-06-28T03:17:09.225Z [NETFORWARDER] Forwarder has changed state to disabled
2026-06-28T03:17:09.227Z [WEBSERVER] Apply Webserver settings
2026-06-28T03:17:09.227Z [WEBSERVER] Set document root to: :/www
2026-06-28T03:17:09.227Z [WEBSERVER] Started: 'HyperHDR WebServer (HTTP)' on port: 8090
2026-06-28T03:17:09.227Z [SSDP] (SSDPHandler.cpp:93) The local address is empty
2026-06-28T03:17:09.227Z [WEBSERVER] Initialize Webserver
2026-06-28T03:17:09.227Z [WEBSERVER] Apply Webserver settings
2026-06-28T03:17:09.227Z [WEBSERVER] Set document root to: :/www
2026-06-28T03:17:09.236Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName: ttyACM0
2026-06-28T03:17:09.236Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation: /dev/ttyACM0
2026-06-28T03:17:09.236Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description: USB Single Serial
2026-06-28T03:17:09.236Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer: 1a86
2026-06-28T03:17:09.236Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0x55d4
2026-06-28T03:17:09.236Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier: 0x1a86
2026-06-28T03:17:09.236Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber: 567E050638
2026-06-28T03:17:09.240Z [WEBSERVER] Setup SSL certificate
2026-06-28T03:17:09.240Z [WEBSERVER] Setup private SSL key
2026-06-28T03:17:09.241Z [WEBSERVER] Started: 'HyperHDR WebServer (HTTPS)' on port: 8092
2026-06-28T03:17:09.241Z [SSDP] (SSDPHandler.cpp:42) SSDPHandler is initializing
2026-06-28T03:17:09.241Z [SSDP] (SSDPHandler.cpp:183) The local address is: 10.1.8.51
2026-06-28T03:17:09.241Z [SSDP] (SSDPServer.cpp:94) Initialize the SSDP server
2026-06-28T03:17:09.241Z [V4L2:USB3 VIDEO: US] Set resolution to: 800 x 600
2026-06-28T03:17:09.241Z [SSDP] Starting the SSDP server
2026-06-28T03:17:09.258Z [V4L2:USB3 VIDEO: US] Set framerate to 60 FPS
2026-06-28T03:17:09.261Z [V4L2:USB3 VIDEO: US] Brightness set to: 50 (default)
2026-06-28T03:17:09.264Z [V4L2:USB3 VIDEO: US] Contrast set to: 50 (default)
2026-06-28T03:17:09.268Z [V4L2:USB3 VIDEO: US] Saturation set to: 50 (default)
2026-06-28T03:17:09.271Z [V4L2:USB3 VIDEO: US] Hue set to: 50 (default)
2026-06-28T03:17:09.271Z [V4L2:USB3 VIDEO: US] (V4L2Grabber.cpp:123) LUT folder location: '/storage/hyperhdr21/share/hyperhdr/lut'
2026-06-28T03:17:09.271Z [V4L2:USB3 VIDEO: US] (LutLoader.cpp:73) LUT file found: /storage/hyperhdr21/.hyperhdr/lut_lin_tables.3d (uncompressed)
2026-06-28T03:17:09.271Z [V4L2:USB3 VIDEO: US] (LutLoader.cpp:89) Index 2 for YUV
2026-06-28T03:17:09.299Z [V4L2:USB3 VIDEO: US] Found and loaded LUT: '/storage/hyperhdr21/.hyperhdr/lut_lin_tables.3d'
2026-06-28T03:17:09.299Z [V4L2:USB3 VIDEO: US] Video pixel format is set to: YUYV
2026-06-28T03:17:09.303Z [V4L2:USB3 VIDEO: US] Started
2026-06-28T03:17:09.344Z [V4L2:USB3 VIDEO: US] Frame too small: 0 != 960000
2026-06-28T03:17:09.344Z [V4L2:USB3 VIDEO: US] Frame too small: 0 != 960000
2026-06-28T03:17:09.344Z [V4L2:USB3 VIDEO: US] Frame too small: 0 != 960000
2026-06-28T03:17:09.344Z [V4L2:USB3 VIDEO: US] Frame too small: 0 != 960000
2026-06-28T03:17:09.351Z [V4L2:USB3 VIDEO: US] Frame too small: 392124 != 960000
2026-06-28T03:17:09.368Z [V4L2:USB3 VIDEO: US] (V4L2Grabber.cpp:1231) Worker's thread count = 4
2026-06-28T03:17:09.370Z [MUXER0] Priority 240 is now active
2026-06-28T03:17:09.370Z [MUXER0] Set visible priority to 240
2026-06-28T03:17:09.370Z [HYPERHDR0] New priority[240], previous [255]
2026-06-28T03:17:09.370Z [HYPERHDR0] New source available -> switch LED-Device on
2026-06-28T03:17:09.370Z [SMOOTHING0] Clearing queued colors before: enabling
2026-06-28T03:17:09.370Z [SMOOTHING0] Smoothing queue is cleared
2026-06-28T03:17:09.370Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:224) setBackLightEnabled: 1
2026-06-28T03:17:09.371Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:17:09.371Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:17:09.540Z [LEDDEVICE0_ADALIGHT] ESP sent: ''
2026-06-28T03:17:09.606Z [LEDDEVICE0_ADALIGHT] DETECTED DEVICE USING HyperSerialEsp8266/HyperSerialESP32/HyperSerialPico FIRMWARE (Welcome! Awa driver 11. NeoPixelBus SK6812 cold GRBW.) at 66 msec
2026-06-28T03:17:09.606Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:63) Switch on
2026-06-28T03:17:09.606Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:139) Power On
2026-06-28T03:17:09.606Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:246) Enable the device
2026-06-28T03:17:09.606Z [COMPONENTCTRL0] LED device: enabled
2026-06-28T03:17:10.552Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:17:10.740Z [NET_DISCOVERY] Found ESP board at ttyACM0:-1 (USB Single Serial)
2026-06-28T03:17:10.729Z [SERVICE_mDNS] Starting the network discovery thread
2026-06-28T03:17:10.981Z [WEBSERVER] Web server resources initialized: /storage/hyperhdr21/share/hyperhdr/bin/../lib/web_resources.rcc
2026-06-28T03:17:11.190Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::ffff:10.1.2.240
2026-06-28T03:17:11.322Z [WEBSOCKET] (HyperAPI.cpp:946) log streaming activated for client ::ffff:10.1.2.240
2026-06-28T03:17:11.348Z [WEBSOCKET] (WebSocketClient.cpp:40) New connection from ::ffff:10.1.2.240
2026-06-28T03:17:14.077Z [WEBSOCKET] (HyperAPI.cpp:955) log streaming deactivated for client ::ffff:10.1.2.240
2026-06-28T03:17:22.306Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":315}]
2026-06-28T03:17:22.317Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"USB Single Serial (/dev/ttyACM0)","value":"ttyACM0"},{"name":" (/dev/ttyS0)","value":"ttyS0"},{"name":" (/dev/ttyS1)","value":"ttyS1"},{"name":" (/dev/ttyS2)","value":"ttyS2"},{"name":" (/dev/ttyS3)","value":"ttyS3"}],"ledDeviceType":"adalight"}]
2026-06-28T03:17:23.178Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:17:27.575Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:285) Stop device
2026-06-28T03:17:27.575Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:296) Disable the device
2026-06-28T03:17:27.575Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:89) Switch off
2026-06-28T03:17:27.575Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:543) Set LED strip to black/power off
2026-06-28T03:17:27.580Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:146) Flush was successful
2026-06-28T03:17:27.604Z [LEDDEVICE0_ADALIGHT] Received goodbye: 'RGBW => Gain: 255/255, red: 160, green: 160, blue: 160
HyperHDR frames: 60 (FPS), receiv.: 60, good: 60, incompl.: 0, mem1: 4212, mem2: 3232, heap: 301968
RGBW => Gain: 255/255, red:' (184)
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:164) Serial port is closed: ttyACM0
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] Stopped LedDevice 'adalight'
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] Start LedDevice 'adalight'.
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:336) deviceConfig: [{"awa_mode":true,"colorOrder":"rgb","currentLedCount":300,"espHandshake":true,"forceSerialDetection":false,"hardwareLedCount":null,"maxRetry":5,"output":"ttyACM0","rate":2000000,"refreshTime":0,"smoothingRefreshTime":0,"type":"adalight","white_channel_calibration":false}]
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:432) Refresh interval updated to 0ms
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:50) DeviceType : adalight
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:51) LedCount : 300
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:52) RefreshTime : 0
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:67) Device name : ttyACM0
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:68) Auto selection: 0
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:69) Baud rate : 2000000
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:70) ESP handshake : ON
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:71) Force ESP/Pico Detection : OFF
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:72) Delayed open : 0
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:73) Retry limit : 5
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] (DriverSerialAdalight.cpp:78) Adalight driver with activated high speeed & data integration check AWA protocol
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] (DriverSerialAdalight.cpp:87) Adalight header for 300 leds: Awa 0x01 0x2b 0x7f
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:246) Enable the device
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] Opening UART: ttyACM0
2026-06-28T03:17:27.606Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): ttyACM0, Baud rate [2000000]bps
2026-06-28T03:17:27.607Z [COMPONENTCTRL0] LED device: disabled
2026-06-28T03:17:27.617Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName: ttyACM0
2026-06-28T03:17:27.617Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation: /dev/ttyACM0
2026-06-28T03:17:27.617Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description: USB Single Serial
2026-06-28T03:17:27.617Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer: 1a86
2026-06-28T03:17:27.617Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0x55d4
2026-06-28T03:17:27.617Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier: 0x1a86
2026-06-28T03:17:27.617Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber: 567E050638
2026-06-28T03:17:27.921Z [LEDDEVICE0_ADALIGHT] ESP sent: ''
2026-06-28T03:17:27.987Z [LEDDEVICE0_ADALIGHT] ESP sent: ''3&%!l'
2026-06-28T03:17:27.987Z [LEDDEVICE0_ADALIGHT] ESP sent: 'xH Hk-J/ SH'
2026-06-28T03:17:28.989Z [LEDDEVICE0_ADALIGHT] Could not detect HyperSerialEsp8266/HyperSerialESP32/HyperSerialPico device
2026-06-28T03:17:28.989Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:63) Switch on
2026-06-28T03:17:28.989Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:139) Power On
2026-06-28T03:17:28.989Z [COMPONENTCTRL0] LED device: enabled
2026-06-28T03:17:46.744Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":438}]
2026-06-28T03:17:46.755Z [WEBSOCKET] (HyperAPI.cpp:1121) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":"USB Single Serial (/dev/ttyACM0)","value":"ttyACM0"},{"name":" (/dev/ttyS0)","value":"ttyS0"},{"name":" (/dev/ttyS1)","value":"ttyS1"},{"name":" (/dev/ttyS2)","value":"ttyS2"},{"name":" (/dev/ttyS3)","value":"ttyS3"}],"ledDeviceType":"adalight"}]
2026-06-28T03:17:54.014Z [WEBSOCKET] (HyperAPI.cpp:1097) message: [{"command":"leddevice","ledDeviceType":"","params":{},"subcommand":"hasLedClock","tan":1}]
2026-06-28T03:18:10.627Z [SMOOTHING0] High resolution clock is NOT STEADY!
2026-06-28T03:18:10.627Z [SMOOTHING0] Clearing queued colors before: enabling
2026-06-28T03:18:10.627Z [SMOOTHING0] Smoothing queue is cleared
2026-06-28T03:18:10.627Z [COMPONENTCTRL0] Smoothing: enabled
2026-06-28T03:18:10.627Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:422) Refresh rate = 50.00 Hz
2026-06-28T03:18:10.627Z [SMOOTHING0] Creating config (0) => type: Alternative, pause: false, settlingTime: 65ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
2026-06-28T03:18:10.627Z [SMOOTHING0] Clearing queued colors before: enabling. Smoothing configuration changed: restarting timer.
2026-06-28T03:18:10.627Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:366) Starting timer with interval = 20ms
2026-06-28T03:18:10.627Z [SMOOTHING0] Smoothing queue is cleared
2026-06-28T03:18:10.627Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:432) Refresh interval updated to 20ms
2026-06-28T03:18:10.627Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:447) LED refresh interval adjustment caused by smoothing configuration change to 20ms (proposed: 20ms)
2026-06-28T03:18:10.627Z [SMOOTHING0] Selecting config (0) => type: Alternative, pause: false, settlingTime: 65ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
2026-06-28T03:18:10.628Z [SMOOTHING0] Using alternative smoothing input (0)
2026-06-28T03:18:10.667Z [SMOOTHING0] Using alternative smoothing procedure (0)
2026-06-28T03:18:20.746Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:18:28.784Z [WEBSOCKET] (HyperAPI.cpp:946) log streaming activated for client ::ffff:10.1.2.240
2026-06-28T03:18:32.339Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:18:47.481Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:18:49.497Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:18:59.924Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:19:01.873Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:19:09.184Z [PERFORMANCE] [USB: FPS = 60.03, decoding = 1ms, frames = 3603, invalid = 0, mode = direct], [INSTANCE0: FPS = 60.05, processed = 3603], [LED0: FPS = 50.20, send = 3012, processed = 3012, dropped = 0]
2026-06-28T03:19:09.184Z [V4L2:USB3 VIDEO: US] Video cache: size: 2, hits: 7191, needed: 1, cleanup: 0, limit: 8
2026-06-28T03:19:10.418Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:19:11.917Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:19:43.933Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:19:55.260Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:20:09.188Z [PERFORMANCE] [USB: FPS = 60.03, decoding = 1ms, frames = 3602, invalid = 0, mode = direct], [INSTANCE0: FPS = 60.03, processed = 3602], [LED0: FPS = 50.00, send = 3001, processed = 3001, dropped = 0]
2026-06-28T03:20:11.984Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:20:12.068Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:164) Serial port is closed: ttyACM0
2026-06-28T03:20:12.068Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:380) Stopping refresh timer
2026-06-28T03:20:12.068Z [LEDDEVICE0_ADALIGHT] Device 'adalight' is disabled due to an error: 'Rs232 SerialPortError: Resource temporarily unavailable'
2026-06-28T03:20:12.068Z [COMPONENTCTRL0] LED device: disabled
2026-06-28T03:20:12.068Z [PERFORMANCE] [USB: FPS = 60.03, decoding = 1ms, frames = 3602, invalid = 0, mode = direct], [INSTANCE0: FPS = 60.03, processed = 3602]
2026-06-28T03:20:13.970Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:246) Enable the device
2026-06-28T03:20:13.970Z [LEDDEVICE0_ADALIGHT] Opening UART: ttyACM0
2026-06-28T03:20:13.970Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): ttyACM0, Baud rate [2000000]bps
2026-06-28T03:20:13.982Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName:
2026-06-28T03:20:13.982Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation:
2026-06-28T03:20:13.982Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description:
2026-06-28T03:20:13.982Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer:
2026-06-28T03:20:13.982Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0x0
2026-06-28T03:20:13.982Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier: 0x0
2026-06-28T03:20:13.982Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber:
2026-06-28T03:20:13.982Z [LEDDEVICE0_ADALIGHT] Device 'adalight' is disabled due to an error: 'Invalid serial device name: [ttyACM0]!'
2026-06-28T03:20:13.982Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:372) Device is not ready to start a timer
2026-06-28T03:20:16.437Z [LEDDEVICE0_ADALIGHT] The LED device is not ready... trying to reconnect (try 1/5).
2026-06-28T03:20:16.437Z [LEDDEVICE0_ADALIGHT] Opening UART: ttyACM0
2026-06-28T03:20:16.437Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): ttyACM0, Baud rate [2000000]bps
2026-06-28T03:20:16.447Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName:
2026-06-28T03:20:16.447Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation:
2026-06-28T03:20:16.447Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description:
2026-06-28T03:20:16.447Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer:
2026-06-28T03:20:16.447Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0x0
2026-06-28T03:20:16.447Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier: 0x0
2026-06-28T03:20:16.447Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber:
2026-06-28T03:20:16.447Z [LEDDEVICE0_ADALIGHT] Device 'adalight' is disabled due to an error: 'Invalid serial device name: [ttyACM0]!'
2026-06-28T03:20:16.447Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:372) Device is not ready to start a timer
2026-06-28T03:20:17.830Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:20:18.937Z [LEDDEVICE0_ADALIGHT] The LED device is not ready... trying to reconnect (try 2/5).
2026-06-28T03:20:18.937Z [LEDDEVICE0_ADALIGHT] Opening UART: ttyACM0
2026-06-28T03:20:18.937Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): ttyACM0, Baud rate [2000000]bps
2026-06-28T03:20:18.948Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName: ttyACM0
2026-06-28T03:20:18.948Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation: /dev/ttyACM0
2026-06-28T03:20:18.948Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description: USB Single Serial
2026-06-28T03:20:18.948Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer: 1a86
2026-06-28T03:20:18.948Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0x55d4
2026-06-28T03:20:18.948Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier: 0x1a86
2026-06-28T03:20:18.948Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber: 567E039329
2026-06-28T03:20:19.253Z [LEDDEVICE0_ADALIGHT] ESP sent: ''
2026-06-28T03:20:19.293Z [LEDDEVICE0_ADALIGHT] DETECTED DEVICE USING HyperSerialEsp8266/HyperSerialESP32/HyperSerialPico FIRMWARE (Welcome! Awa driver 7. NeoPixelBus SK6812 cold GRBW. RGBW => Gain: 255/255, red: 160 , green: 160 , blue: 160) at 40 msec
2026-06-28T03:20:19.293Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:63) Switch on
2026-06-28T03:20:19.293Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:139) Power On
2026-06-28T03:20:19.293Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:391) Stopping retry timer
2026-06-28T03:20:19.293Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:366) Starting timer with interval = 20ms
2026-06-28T03:20:19.293Z [COMPONENTCTRL0] LED device: enabled
2026-06-28T03:20:22.911Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:20:29.757Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:20:35.604Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:20:39.685Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:20:49.779Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:20:53.244Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:20:59.624Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:21:02.789Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:21:09.184Z [PERFORMANCE] [USB: FPS = 60.03, decoding = 1ms, frames = 3602, invalid = 0, mode = direct], [INSTANCE0: FPS = 60.05, processed = 3603], [LED0: FPS = 43.98, send = 2638, processed = 2638, dropped = 360]
2026-06-28T03:21:21.112Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:21:40.368Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:22:04.404Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:22:07.270Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:22:09.184Z [PERFORMANCE] [USB: FPS = 60.03, decoding = 1ms, frames = 3602, invalid = 0, mode = direct], [INSTANCE0: FPS = 60.03, processed = 3602], [LED0: FPS = 50.00, send = 3000, processed = 3000, dropped = 0]
2026-06-28T03:22:21.328Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:22:23.410Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:22:27.674Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:22:33.638Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:22:37.885Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:22:41.434Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:23:09.183Z [PERFORMANCE] [USB: FPS = 60.03, decoding = 1ms, frames = 3602, invalid = 0, mode = direct], [INSTANCE0: FPS = 60.03, processed = 3602], [LED0: FPS = 50.00, send = 3000, processed = 3000, dropped = 0]
2026-06-28T03:23:21.012Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:23:22.444Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:23:30.190Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:23:35.404Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:23:39.002Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:23:42.333Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:23:47.913Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:23:49.929Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:23:52.094Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:23:56.975Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:24:00.939Z [IMAGETOLED_MNG0] Total index number is: 124224 (memory: 124224). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:24:04.354Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:24:09.184Z [PERFORMANCE] [USB: FPS = 60.03, decoding = 1ms, frames = 3602, invalid = 0, mode = direct], [INSTANCE0: FPS = 60.03, processed = 3603], [LED0: FPS = 50.00, send = 3000, processed = 3000, dropped = 0]
2026-06-28T03:24:10.200Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:24:14.115Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:24:23.159Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:24:25.242Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:24:36.219Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:24:44.764Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:24:48.279Z [IMAGETOLED_MNG0] Total index number is: 124416 (memory: 124416). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:24:56.774Z [IMAGETOLED_MNG0] Total index number is: 124800 (memory: 124800). User sparse processing is: disabled, image size: 800 x 600, area number: 300
2026-06-28T03:25:09.183Z [PERFORMANCE] [USB: FPS = 60.03, decoding = 1ms, frames = 3602, invalid = 0, mode = direct], [INSTANCE0: FPS = 60.03, processed = 3602], [LED0: FPS = 50.00, send = 3000, pro

Thanks anyways.

0 replies

awawa-dev · 2026-06-27T18:28:08Z

awawa-dev
Jun 27, 2026
Maintainer

I think I asked you about different thing but feel free to perform the diagnostic in your own way but without me. These boards from Ali come in different UART configurations so some things must be tested first.

0 replies

reedy-au · 2026-06-28T04:11:41Z

reedy-au
Jun 28, 2026
Author

oh not at all. Sorry didn't mean it that way.

I understand you don't have access to my equipment and can only see what logs I provide.

I'm pretty sure I've wired it correctly with a level shifter as it's worked for years as a single strip. I should just be able to flash a newer version of hyperserialesp32 right?

I wouldn't be surprised if I'm flashing the board wrong...

I just don't understand why I flash with version 7 and push the board in to my pre-wired pcb with headers and it all works but I flash with any higher version and nothing happens. Tried multiple boards.

I can't get a solid colour to calibrate even though it detects the mhet board with the awa 11 driver in the logs.

I don't want to use a rpi as they are very expensive here and the mhet live board was the goto in the day and have a few of them. Can you recommend another board if this one is not great anymore please?

0 replies

awawa-dev · 2026-06-28T11:25:36Z

awawa-dev
Jun 28, 2026
Maintainer

If in the statistics from this test you can see that the board received frames from HyperHDR, then the problem appears somewhere on the output side. If you're using recommended type of the level shifter, it's hard for me to clearly identify the cause. v7 uses the same I2S timings as v11 when emulating Neopixel.

0 replies

awawa-dev · 2026-06-28T21:27:31Z

awawa-dev
Jun 28, 2026
Maintainer

I'm also thinking of trying Hyperk. If it works, it should at least rule out a hardware problem. Plus, it will soon have HyperSerial support as well.

0 replies

reedy-au · 2026-07-06T22:20:51Z

reedy-au
Jul 6, 2026
Author

Apologies for the delay, life got in the way.

I've installed hyperk on the mhet v2.0 board. I've confirmed this board is using a ch9102f usb to uart bridge chipset

Logs from the mhet are flashing hyperk:
[08:15:45]ets Jul 29 2019 12:21:46
[08:15:45]
[08:15:45]rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
[08:15:45]configsip: 0, SPIWP:0xee
[08:15:45]clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
[08:15:45]mode:DIO, clock div:2
[08:15:45]load:0x3fff0030,len:4640
[08:15:45]load:0x40078000,len:15660
[08:15:45]load:0x40080400,len:3164
[08:15:45]entry 0x4008059c
[08:15:46]E (499) esp_core_dump_flash: No co�fx dump partition found!
[08:15:46]E (499) esp_core_dump_flash: No core dump partition found!

Hyperhdr information:

Platform:
Linux (V4L2)
Video device
USB3 Video: USB3 Video (video0)
Video mode
1280x720x60 YUYV
Controller type:
file
Instance:
First LED instance
Your HyperHDR version:
21.0.0.0

V21 doesn't appear to have hyperk as a controller type. I can't run any newer version than hypderhdr v21 due to missing libraries on the intel nuc with Libreelec 12.2.1.

1 reply

awawa-dev Jul 9, 2026
Maintainer

Use WLED driver in HyperHDR then...Hyperk supports it also.

reedy-au · 2026-07-10T06:37:02Z

reedy-au
Jul 10, 2026
Author

Is there any point?

Hyperk and specifically WLED is for network connections right? They don't have serial support?

my setup uses serial uart_bridge_usb for communication for low latency.

It's bizarre, I have v1 and v2 of the mhet live wemos mini d1. Neither work past hyperserialesp32.v7. Something is funky here, I'd like to know why but I don't know enough to troubleshoot further. I'm happy if someone wants to guide, to flash other firmwares and/or test.

Moving forward, I ordered 6 x esp-s2mini - lolin boards from aliexpress.
(https://www.aliexpress.com/item/1005006157693055.html?spm=a2g0o.order_list.order_list_main.5.33671802Hq1JoM)

Maybe I'll see some difference with the newer firmware versions.

0 replies

awawa-dev · 2026-07-10T11:22:41Z

awawa-dev
Jul 10, 2026
Maintainer

Is there any point?

You're missing that point again... I've already told you that Hyperk will receive HyperSerial as well soon so the LED renderer can be tested even now - so why even you've installed it?. BTW esp32s2 is rather poor choice these days compared to classic esp32 (performance, HyperSerialESP32 support) or esp32-c6 (Wifi6, Parlio, price tag, also CDC for Hyperk HyperSerial).

0 replies

reedy-au · 2026-07-11T07:36:20Z

reedy-au
Jul 11, 2026
Author

BTW esp32s2 is rather poor choice these days compared to classic esp32 (performance, HyperSerialESP32 support) or esp32-c6 (Wifi6, Parlio, price tag, also CDC for Hyperk HyperSerial).

Doh!@
Oh well it was $20 for 6. I'll use them somewhere.

I have a bunch of esp32-s3 mini but I can't use them with hyperserialesp32.

You're missing that point again... I've already told you that Hyperk will receive HyperSerial as well soon so the LED renderer can be tested even now - so why even you've installed it?

I probably am. Sorry. So you mean I should've just swapped out the mhet v2 board with another mhet v2 flashed with hyperk and it should work? I'll go test that.

Sorry for the confusion. Next time I'll add photos as telepathy is not helpful for troubleshooting... ;-)

0 replies

Uh oh!

Trouble with MHET v2.0 board and v9 and v11 hyperserialesp32 - Running HyperHDR v21 stable #138

Uh oh!

reedy-au Jun 27, 2026

Replies: 16 comments · 1 reply

Uh oh!

awawa-dev Jun 27, 2026 Maintainer

Uh oh!

reedy-au Jun 27, 2026 Author

Uh oh!

awawa-dev Jun 27, 2026 Maintainer

Uh oh!

Uh oh!

reedy-au Jun 27, 2026 Author

Uh oh!

awawa-dev Jun 27, 2026 Maintainer

Uh oh!

reedy-au Jun 27, 2026 Author

Uh oh!

awawa-dev Jun 27, 2026 Maintainer

Uh oh!

reedy-au Jun 27, 2026 Author

Uh oh!

Uh oh!

awawa-dev Jun 27, 2026 Maintainer

Uh oh!

reedy-au Jun 28, 2026 Author

Uh oh!

awawa-dev Jun 28, 2026 Maintainer

Uh oh!

awawa-dev Jun 28, 2026 Maintainer

Uh oh!

Uh oh!

reedy-au Jul 6, 2026 Author

Uh oh!

awawa-dev Jul 9, 2026 Maintainer

Uh oh!

reedy-au Jul 10, 2026 Author

Uh oh!

awawa-dev Jul 10, 2026 Maintainer

Uh oh!

reedy-au Jul 11, 2026 Author

reedy-au
Jun 27, 2026

Replies: 16 comments 1 reply

awawa-dev
Jun 27, 2026
Maintainer

reedy-au
Jun 27, 2026
Author

awawa-dev
Jun 27, 2026
Maintainer

reedy-au
Jun 27, 2026
Author

awawa-dev
Jun 27, 2026
Maintainer

reedy-au
Jun 27, 2026
Author

awawa-dev
Jun 27, 2026
Maintainer

reedy-au
Jun 27, 2026
Author

awawa-dev
Jun 27, 2026
Maintainer

reedy-au
Jun 28, 2026
Author

awawa-dev
Jun 28, 2026
Maintainer

awawa-dev
Jun 28, 2026
Maintainer

reedy-au
Jul 6, 2026
Author

awawa-dev Jul 9, 2026
Maintainer

reedy-au
Jul 10, 2026
Author

awawa-dev
Jul 10, 2026
Maintainer

reedy-au
Jul 11, 2026
Author